U-Boot 2011.12 (Jul 29 2014 - 13:40:23)
Plat'Home version: 3.0.0 (Marvell version: 2012_Q4.0p17)

Board: OpenBlocks AX3
SoC:   MV78260 B0
       running 2 CPUs
       Custom configuration
CPU:   Marvell PJ4B (584) v7 (Rev 2) LE
       CPU 0
       CPU    @ 1333 [MHz]
       L2     @ 667 [MHz]
       TClock @ 250 [MHz]
       DDR    @ 667 [MHz]
       DDR 64Bit Width, FastPath Memory Access
       DDR ECC Disabled
DRAM:  1024 MiB

Map:   Code:            0x3feed000:0x3ff9e894
       BSS:             0x3ffef710
       Stack:           0x3f9ccef0
       PageTable:       0x002e0000
       Heap:            0x3f9cd000:0x3feed000

Flash: 128 MiB
MMC:   MRVL_MMC: 0
PEX 0.0(0): Detected No Link.
PEX 0.1(1): Detected No Link.
PEX 0.2(2): Detected No Link.
PEX 0.3(3): Detected No Link.
PEX 2.0(4): Detected No Link.
POST:  mac verify Eth0 PASSED Eth1 PASSED Eth2 PASSED Eth3 PASSED
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Host Mode
Power Off External Interface
Modules Detected:
Net:   egiga0, egiga1, egiga2, egiga3
Hit any key to stop autoboot:  0

Run Boot Selection Script

*** SW 1 IS OFF ***

*** SW 2 IS OFF ***

*** SW 3 IS OFF, Standard Boot ***

Bootargs: root=/dev/ram rootdelay=0 vmalloc=240M 
mtdparts=cfi_flash_0:0xe0000(uboot)ro,0x40000(env),0x20000(tstprg)ro,
0x600000(config),0x2800000(linux),
0x30c0000(user),0x2000000(opt) console=ttyS0,115200
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   OBSAX3 4.1.25-0
   Created:      2016-06-09   3:37:37 UTC
   Image Type:   ARM Linux Multi-File Image (uncompressed)
   Data Size:    40131173 Bytes = 38.3 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Contents:
      Image 0: 2300932 Bytes = 2.2 MiB
      Image 1: 37830229 Bytes = 36.1 MiB
   Verifying Checksum ... OK
## Loading init Ramdisk from multi component Legacy Image at 02000000 ...
   Loading Multi-File Image ... OK
OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.1.25 (root@release-firmware-all) (gcc version 4.9.2 ( 4.9.2-10) )
#1 SMP PREEMPT Thu Jun 9 12:33:29 JST 2016
[    0.000000] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine model: PlatHome OpenBlocks AX3-4 board
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] PERCPU: Embedded 12 pages/cpu @ef6d0000 s17152 r8192 d23808 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260415
[    0.000000] Kernel command line:  root=/dev/ram rootdelay=0 vmalloc=240M 
mtdparts=cfi_flash_0:0xe0000(uboot)ro,0x40000(env),0x20000(tstprg)ro,0x600000(config),
0x2800000(linux),0x30c0000(user),0x2000000(opt) console=ttyS0,115200
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 995176K/1048572K available (4416K kernel code, 175K rwdata, 
1228K rodata, 208K init, 177K bss, 53396K reserved, 0K cma-reserved, 262140K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xf0800000 - 0xff000000   ( 232 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc058b470   (5646 kB)
[    0.000000]       .init : 0xc058c000 - 0xc05c0000   ( 208 kB)
[    0.000000]       .data : 0xc05c0000 - 0xc05ebd00   ( 176 kB)
[    0.000000]        .bss : 0xc05ebd00 - 0xc0618264   ( 178 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] L2C: DT/platform modifies aux control register: 0x1a696b10 -> 0x1a696b12
[    0.000000] Aurora cache controller enabled, 16 ways, 1024 kB
[    0.000000] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a696b12
[    0.000008] sched_clock: 32 bits at 25MHz, resolution 40ns, 
wraps every 85899345900ns
[    0.000024] clocksource armada_370_xp_clocksource: mask: 0xffffffff 
max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[    0.000270] Console: colour dummy device 80x30
[    0.000287] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[    0.090104] pid_max: default: 32768 minimum: 301
[    0.090199] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.090208] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.090600] Initializing cgroup subsys blkio
[    0.090612] Initializing cgroup subsys memory
[    0.090634] Initializing cgroup subsys devices
[    0.090643] Initializing cgroup subsys freezer
[    0.090656] Initializing cgroup subsys net_cls
[    0.090664] Initializing cgroup subsys net_prio
[    0.090690] CPU: Testing write buffer coherency: ok
[    0.090850] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.091118] Setting up static identity map for 0x8280 - 0x82d8
[    0.091347] mvebu-soc-id: MVEBU SoC ID=0x7846, Rev=0x2
[    0.091444] mvebu-pmsu: Initializing Power Management Service Unit
[    0.150275] Booting CPU 1
[    0.190094] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.190158] Brought up 2 CPUs
[    0.190169] SMP: Total of 2 processors activated (2664.03 BogoMIPS).
[    0.190175] CPU: All CPU(s) started in SVC mode.
[    0.190549] devtmpfs: initialized
[    0.193371] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[    0.193675] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 19112604462750000 ns
[    0.193986] pinctrl core: initialized pinctrl subsystem
[    0.194424] NET: Registered protocol family 16
[    0.194618] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.220084] cpuidle: using governor ladder
[    0.250081] cpuidle: using governor menu
[    0.257268] hw-breakpoint: Debug register access (0xee003e17) 
caused undefined instruction on CPU 1
[    0.257277] hw-breakpoint: CPU 1 failed to disable vector catch
[    0.257286] hw-breakpoint: Debug register access (0xee003e17)
caused undefined instruction on CPU 0
[    0.291084] vgaarb: loaded
[    0.291415] SCSI subsystem initialized
[    0.292102] usbcore: registered new interface driver usbfs
[    0.292194] usbcore: registered new interface driver hub
[    0.292279] usbcore: registered new device driver usb
[    0.293323] Switched to clocksource armada_370_xp_clocksource
[    0.293546] FS-Cache: Loaded
[    0.300957] NET: Registered protocol family 2
[    0.301516] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.301567] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.301627] TCP: Hash tables configured (established 8192 bind 8192)
[    0.301674] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.301698] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.301841] NET: Registered protocol family 1
[    0.302039] Trying to unpack rootfs image as initramfs...
[    6.252944] rootfs image is not initramfs (no cpio magic); looks like an initrd
[    6.348788] Freeing initrd memory: 36948K (c2231000 - c4646000)
[    6.348976] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[    6.350080] futex hash table entries: 512 (order: 3, 32768 bytes)
[    6.350785] VFS: Disk quotas dquot_6.6.0
[    6.350835] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    6.351142] aufs 4.1-20160523
[    6.351855] bounce: pool size: 64 pages
[    6.351911] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    6.351924] io scheduler noop registered
[    6.351935] io scheduler deadline registered
[    6.351968] io scheduler cfq registered (default)
[    6.352520] armada-xp-pinctrl d0018000.pin-ctrl: registered pinctrl driver
[    6.352982] irq: Cannot allocate irq_descs @ IRQ43, assuming pre-allocated
[    6.353277] irq: Cannot allocate irq_descs @ IRQ75, assuming pre-allocated
[    6.353500] irq: Cannot allocate irq_descs @ IRQ107, assuming pre-allocated
[    6.353903] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
[    6.353916] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
[    6.353924] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[    6.353933] pci_bus 0000:00: root bus resource [bus 00-ff]
[    6.354136] PCI: bus0: Fast back to back transfers disabled
[    6.354147] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    6.354255] PCI: bus1: Fast back to back transfers enabled
[    6.354289] pci 0000:00:01.0: PCI bridge to [bus 01]
[    6.354408] mv_xor d0060900.xor: Marvell shared XOR driver
[    6.393453] mv_xor d0060900.xor: Marvell XOR: ( xor cpy )
[    6.433396] mv_xor d0060900.xor: Marvell XOR: ( xor cpy )
[    6.433500] mv_xor d00f0900.xor: Marvell shared XOR driver
[    6.473395] mv_xor d00f0900.xor: Marvell XOR: ( xor cpy )
[    6.513394] mv_xor d00f0900.xor: Marvell XOR: ( xor cpy )
[    6.516442] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    6.517602] console [ttyS0] disabled
[    6.537700] d0012000.serial: ttyS0 at MMIO 0xd0012000 
(irq = 20, base_baud = 15625000) is a 16550A
[    7.235403] console [ttyS0] enabled
[    7.259340] d0012100.serial: ttyS1 at MMIO 0xd0012100 
(irq = 21, base_baud = 15625000) is a 16550A
[    7.270594] brd: module loaded
[    7.277079] loop: module loaded
[    7.280753] sata_mv d00a0000.sata: slots 32 ports 2
[    7.286780] scsi host0: sata_mv
[    7.290250] scsi host1: sata_mv
[    7.293587] ata1: SATA max UDMA/133 irq 31
[    7.297697] ata2: SATA max UDMA/133 irq 31
[    7.302328] libphy: orion_mdio_bus: probed
[    7.308987] mvneta d0070000.ethernet eth0: Using hardware mac address 00:0a:85:07:**:**
[    7.318325] mvneta d0074000.ethernet eth1: Using hardware mac address 00:0a:85:07:**:** 
[    7.327729] mvneta d0030000.ethernet eth2: Using hardware mac address 00:0a:85:07:**:**
[    7.337122] mvneta d0034000.ethernet eth3: Using hardware mac address 00:0a:85:07:**:**
[    7.345260] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.351810] ehci-pci: EHCI PCI platform driver
[    7.356392] ehci-orion: EHCI orion driver
[    7.360518] orion-ehci d0050000.usb: EHCI Host Controller
[    7.365965] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 1
[    7.373641] orion-ehci d0050000.usb: irq 27, io mem 0xd0050000
[    7.393344] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00
[    7.399420] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    7.406246] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.413500] usb usb1: Product: EHCI Host Controller
[    7.418391] usb usb1: Manufacturer: Linux 4.1.25 ehci_hcd
[    7.423816] usb usb1: SerialNumber: d0050000.usb
[    7.428983] hub 1-0:1.0: USB hub found
[    7.432771] hub 1-0:1.0: 1 port detected
[    7.437035] orion-ehci d0051000.usb: EHCI Host Controller
[    7.442463] orion-ehci d0051000.usb: new USB bus registered, assigned bus number 2
[    7.450132] orion-ehci d0051000.usb: irq 28, io mem 0xd0051000
[    7.473340] orion-ehci d0051000.usb: USB 2.0 started, EHCI 1.00
[    7.479400] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    7.486226] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.493481] usb usb2: Product: EHCI Host Controller
[    7.498372] usb usb2: Manufacturer: Linux 4.1.25 ehci_hcd
[    7.503798] usb usb2: SerialNumber: d0051000.usb
[    7.508915] hub 2-0:1.0: USB hub found
[    7.512702] hub 2-0:1.0: 1 port detected
[    7.517414] usbcore: registered new interface driver usb-storage
[    7.523765] i2c /dev entries driver
[    7.529789] rtc-s35390a 1-0030: rtc core: registered rtc-s35390a as rtc0
[    7.537639] ledtrig-cpu: registered to indicate activity on CPUs
[    7.543891] hidraw: raw HID events driver (C) Jiri Kosina
[    7.550982] cfi_flash_0: Found 1 x16 devices at 0x0 in 16-bit bank. 
Manufacturer ID 0x000089 Chip ID 0x00227e
[    7.561033] Amd/Fujitsu Extended Query Table at 0x0040
[    7.566295]   Amd/Fujitsu Extended Query version 1.3.
[    7.571371] number of CFI chips: 1
[    7.574909] 7 cmdlinepart partitions found on MTD device cfi_flash_0
[    7.581285] Creating 7 MTD partitions on "cfi_flash_0":
[    7.586621] 0x000000000000-0x0000000e0000 : "uboot"
[    7.592294] 0x0000000e0000-0x000000120000 : "env"
[    7.597385] 0x000000120000-0x000000140000 : "tstprg"
[    7.602802] 0x000000140000-0x000000740000 : "config"
[    7.608269] 0x000000740000-0x000002f40000 : "linux"
[    7.613637] 0x000002f40000-0x000006000000 : "user"
[    7.618889] 0x000006000000-0x000008000000 : "opt"
[    7.624764] Initializing XFRM netlink socket
[    7.629099] NET: Registered protocol family 17
[    7.633634] NET: Registered protocol family 15
[    7.638168] ThumbEE CPU extension supported.
[    7.642469] Registering SWP/SWPB emulation handler
[    7.643772] ata1: SATA link down (SStatus 0 SControl F300)
[    7.653416] registered taskstats version 1
[    7.659664] input: soc:internal-regs:gpio_keys as /devices/platform/soc/
soc:internal-regs/soc:internal-regs:gpio_keys/input/input0
[    7.672475] rtc-s35390a 1-0030: setting system clock to 2025-05-22 09:59:46 UTC (1747907986)
[    7.994071] ata2: SATA link down (SStatus 0 SControl F300)
[    8.014171] RAMDISK: lzma image found at block 0
[   25.541399] EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
[   25.549415] EXT4-fs (ram0): mounting ext2 file system using the ext4 subsystem
[   25.558217] EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
[   25.565479] VFS: Mounted root (ext2 filesystem) readonly on device 1:0.
[   25.572476] devtmpfs: mounted
[   25.575720] Freeing unused kernel memory: 208K (c058c000 - c05c0000)
Mount failed for selinuxfs on /sys/fs/selinux:  No such file or directory
INIT: version 2.88 booting
[....] Starting the hotplug events dispatcher: udevd[   26.035099] 
systemd-udevd[691]: starting version 215
[   26.043908] random: udevd urandom read with 0 bits of entropy available
. ok
[....] Synthesizing the initial hotplug events...[   26.190848] orion_wdt: 
Initial timeout 171 sec
done.
[ ok ] Waiting for /dev to be fully populated...done.
[   29.588793] EXT4-fs (ram0): re-mounted. Opts: (null)
Extract userland files from FlashROM(mtd5)... done.
Extract /etc config files from FlashROM(mtd3)... done.
[   51.004695] aufs test_add:284:mount[968]: uid/gid/perm /root 0/0/0700, 0/0/0755
[....] Starting the hotplug events dispatcher: udevd[   51.201150] 
systemd-udevd[1002]: starting version 215
. ok
[ ok ] Synthesizing the initial hotplug events...done.
[ ok ] Waiting for /dev to be fully populated...done.
Extract optional files from FlashROM(mtd6)... done.
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Cleaning up temporary files... /tmp.
[info] Loading kernel module ipv6.
[   67.726316] NET: Registered protocol family 10
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[ ok ] Configuring network interfaces...done.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[ ok ] Starting enhanced syslogd: rsyslogd.
[ ok ] Starting uuid generator: uuidd.
[ ok ] Starting periodic command scheduler: cron.
Inserting openvswitch module.
Starting ovsdb-server.
Configuring Open vSwitch system IDs.
Starting ovs-vswitchd.
Enabling remote OVSDB managers.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Restarting periodic command scheduler: cron[....] Stopping periodic comma
[ ok heduler: cron.
[ ok ] Starting periodic command scheduler: cron.

tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes

Debian GNU/Linux 8 obsax3 ttyS0

obsax3 login: not found MFP...

Debian GNU/Linux 8 obsax3 ttyS0

obsax3 login: root
Password:

Login incorrect
obsax3 login: root
Password:

Login incorrect
obsax3 login:

///////////////////////////////////////////////////
U-Boot 2011.12 (Jul 29 2014 - 13:40:23)
Plat'Home version: 3.0.0 (Marvell version: 2012_Q4.0p17)

Board: OpenBlocks AX3
SoC:   MV78260 B0
       running 2 CPUs
       Custom configuration
CPU:   Marvell PJ4B (584) v7 (Rev 2) LE
       CPU 0
       CPU    @ 1333 [MHz]
       L2     @ 667 [MHz]
       TClock @ 250 [MHz]
       DDR    @ 667 [MHz]
       DDR 64Bit Width, FastPath Memory Access
       DDR ECC Disabled
DRAM:  1024 MiB
・
Map:   Code:            0x3feed000:0x3ff9e894
       BSS:             0x3ffef710
       Stack:           0x3f9ccef0
       PageTable:       0x002e0000
       Heap:            0x3f9cd000:0x3feed000

Flash: 128 MiB
MMC:   MRVL_MMC: 0
PEX 0.0(0): Detected No Link.
PEX 0.1(1): Detected No Link.
PEX 0.2(2): Detected No Link.
PEX 0.3(3): Detected No Link.
PEX 2.0(4): Detected No Link.
POST:  mac verify Eth0 PASSED Eth1 PASSED Eth2 PASSED Eth3 PASSED
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Host Mode
Power Off External Interface
Modules Detected:
Net:   egiga0, egiga1, egiga2, egiga3
Hit any key to stop autoboot:  0
openblocks>
openblocks> printenv
CASset=min
MALLOC_len=5
MPmode=SMP
allupd=bubt && run _tp_load_prog && run os_load_prog
autoload=no
baudrate=115200
boot_order=hd_scr hd_img pxe net_img net_scr
bootargs_dflt=$console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath 
ip=$ipaddr:$serverip$bootargs_end $mvNetConfig 
video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel
bootcmd=echo;echo Run Boot Selection Script;echo;run _phase_1
bootdelay=0
cacheShare=no
clr_env=resetenv
console=ttyS0
device_partition=0:1
disL2Cache=yes
disL2Prefetch=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaCpuStream=no
enaDCPref=yes
enaFPU=yes
enaICPref=yes
enaLPAE=no
enaMonExt=no
enaWrAllo=no
eth1addr=00:0a:85:07:**:**
eth1mtu=1500
eth2addr=00:0a:85:07:**:**
eth2mtu=1500
eth3addr=00:0a:85:07:**:**
eth3mtu=1500
ethact=egiga0
ethaddr=00:0a:85:07:**:**
ethmtu=1500
fdt_addr=2040000
ide_path=/
initrd_name=uInitrd
ipaddr=192.168.254.254
kernel_addr_r=2080000
loadaddr=0x02000000
loads_echo=0
mtd_linux=0x2800000
mtd_opt=0x2000000
mtd_opt_kb=32768
mtd_user=0x30c0000
mtdids=nor0=cfi_flash_0
mtdparts=cfi_flash_0:0xe0000(uboot)ro,0x40000(env),0x20000(tstprg)ro,
0x600000(config),0x2800000(linux),0x30c0000(user),0x2000000(opt)
netmask=255.255.255.0
netretry=no
os_load_boot=run _os_load;run _ramargs;run _addtty;run _show_bootargs; bootm ${_kernel_addr_r}
os_load_prog=setenv target os;run _load_prog
pcieTune=no
pexMode=RC
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rcvrip=169.254.100.100
root=/dev/ram
rootdelay=0
run_tp=cp.b ${_tp_addr} ${_tp_addr_r} 0x20000;go ${_tp_entry}
sata_delay_reset=0
sata_dma_mode=yes
sata_fs=ext2
satadev=0:1
script_addr_r=3000000
script_name=boot.scr
setL2CacheWT=no
stderr=serial
stdin=serial
stdout=serial
tftpserver=192.168.254.1
upd=bubt
update_linux=led 1 bl;usb start;run _linux_usb_load;usb stop;led 0
update_opt=led 1 bl; usb start;run _opt_usb_load;usb stop;led 0
update_tp=led 1 bl;usb start;run _tp_usb_load;usb stop;led 0
update_uboot=led 1 bl; usb start;run _uboot_usb_load;usb stop;led 0
usb0Mode=host
usb1Mode=host
usb2Mode=host
usbActive=0
vmalloc=240M

Environment size: 5977/131067 bytes
openblocks>